当前位置：首页 > news >正文

做的网站为什么百度搜不到c做项目的网站

news 2025/9/17 23:24:55

做的网站为什么百度搜不到,c做项目的网站,一个人做网站赚钱,网站策划的知识为什么不用HAL库，使用HAL库捕获输入一个通道还尚可，多通道捕获由于HAL的回调函数不符合我的要求，干脆直接切换到LL库。网上找了许多，代码处理写的不符合我的要求，这里记录一下我的调试过程。 TIM2输出1路PWM信号&#…

为什么不用HAL库，使用HAL库捕获输入一个通道还尚可，多通道捕获由于HAL的回调函数不符合我的要求，干脆直接切换到LL库。网上找了许多，代码处理写的不符合我的要求，这里记录一下我的调试过程。
TIM2输出1路PWM信号，使用1分3杜邦线接到TIM3的CH2-CH3-CH4通道进行捕获输入。
在这里插入图片描述


#include "tim.h"/* TIM2 init function */
void MX_TIM2_Init(void)
{LL_TIM_InitTypeDef TIM_InitStruct = {0};LL_TIM_OC_InitTypeDef TIM_OC_InitStruct = {0};LL_GPIO_InitTypeDef GPIO_InitStruct = {0};/* Peripheral clock enable */LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_TIM2);TIM_InitStruct.Prescaler = 63;TIM_InitStruct.CounterMode = LL_TIM_COUNTERMODE_UP;TIM_InitStruct.Autoreload = 9999;TIM_InitStruct.ClockDivision = LL_TIM_CLOCKDIVISION_DIV1;LL_TIM_Init(TIM2, &TIM_InitStruct);LL_TIM_DisableARRPreload(TIM2);LL_TIM_SetClockSource(TIM2, LL_TIM_CLOCKSOURCE_INTERNAL);LL_TIM_OC_EnablePreload(TIM2, LL_TIM_CHANNEL_CH2);TIM_OC_InitStruct.OCMode = LL_TIM_OCMODE_PWM1;TIM_OC_InitStruct.OCState = LL_TIM_OCSTATE_DISABLE;TIM_OC_InitStruct.OCNState = LL_TIM_OCSTATE_DISABLE;TIM_OC_InitStruct.CompareValue = 5000;TIM_OC_InitStruct.OCPolarity = LL_TIM_OCPOLARITY_HIGH;LL_TIM_OC_Init(TIM2, LL_TIM_CHANNEL_CH2, &TIM_OC_InitStruct);LL_TIM_OC_DisableFast(TIM2, LL_TIM_CHANNEL_CH2);LL_TIM_SetTriggerOutput(TIM2, LL_TIM_TRGO_RESET);LL_TIM_DisableMasterSlaveMode(TIM2);/* USER CODE BEGIN TIM2_Init 2 *//* USER CODE END TIM2_Init 2 */LL_IOP_GRP1_EnableClock(LL_IOP_GRP1_PERIPH_GPIOB);/**TIM2 GPIO ConfigurationPB3     ------> TIM2_CH2*/GPIO_InitStruct.Pin = LL_GPIO_PIN_3;GPIO_InitStruct.Mode = LL_GPIO_MODE_ALTERNATE;GPIO_InitStruct.Speed = LL_GPIO_SPEED_FREQ_LOW;GPIO_InitStruct.OutputType = LL_GPIO_OUTPUT_PUSHPULL;GPIO_InitStruct.Pull = LL_GPIO_PULL_NO;GPIO_InitStruct.Alternate = LL_GPIO_AF_2;LL_GPIO_Init(GPIOB, &GPIO_InitStruct);//-------------------------------------------LL_TIM_OC_SetCompareCH2(TIM2,2000);LL_TIM_CC_EnableChannel(TIM2,LL_TIM_CHANNEL_CH2);LL_TIM_EnableCounter(TIM2);}
/* TIM3 init function */
void MX_TIM3_Init(void)
{LL_TIM_InitTypeDef TIM_InitStruct = {0};LL_GPIO_InitTypeDef GPIO_InitStruct = {0};/* Peripheral clock enable */LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_TIM3);LL_IOP_GRP1_EnableClock(LL_IOP_GRP1_PERIPH_GPIOA);LL_IOP_GRP1_EnableClock(LL_IOP_GRP1_PERIPH_GPIOB);/**TIM3 GPIO ConfigurationPA7   ------> TIM3_CH2PB0   ------> TIM3_CH3PB1   ------> TIM3_CH4*/GPIO_InitStruct.Pin = LL_GPIO_PIN_7;GPIO_InitStruct.Mode = LL_GPIO_MODE_ALTERNATE;GPIO_InitStruct.Speed = LL_GPIO_SPEED_FREQ_LOW;GPIO_InitStruct.OutputType = LL_GPIO_OUTPUT_PUSHPULL;GPIO_InitStruct.Pull = LL_GPIO_PULL_NO;GPIO_InitStruct.Alternate = LL_GPIO_AF_1;LL_GPIO_Init(GPIOA, &GPIO_InitStruct);GPIO_InitStruct.Pin = LL_GPIO_PIN_0;GPIO_InitStruct.Mode = LL_GPIO_MODE_ALTERNATE;GPIO_InitStruct.Speed = LL_GPIO_SPEED_FREQ_LOW;GPIO_InitStruct.OutputType = LL_GPIO_OUTPUT_PUSHPULL;GPIO_InitStruct.Pull = LL_GPIO_PULL_NO;GPIO_InitStruct.Alternate = LL_GPIO_AF_1;LL_GPIO_Init(GPIOB, &GPIO_InitStruct);GPIO_InitStruct.Pin = LL_GPIO_PIN_1;GPIO_InitStruct.Mode = LL_GPIO_MODE_ALTERNATE;GPIO_InitStruct.Speed = LL_GPIO_SPEED_FREQ_LOW;GPIO_InitStruct.OutputType = LL_GPIO_OUTPUT_PUSHPULL;GPIO_InitStruct.Pull = LL_GPIO_PULL_NO;GPIO_InitStruct.Alternate = LL_GPIO_AF_1;LL_GPIO_Init(GPIOB, &GPIO_InitStruct);/* TIM3 interrupt Init */NVIC_SetPriority(TIM3_IRQn, 0);NVIC_EnableIRQ(TIM3_IRQn);/* USER CODE BEGIN TIM3_Init 1 *//* USER CODE END TIM3_Init 1 */TIM_InitStruct.Prescaler = 63;TIM_InitStruct.CounterMode = LL_TIM_COUNTERMODE_UP;TIM_InitStruct.Autoreload = 65535;TIM_InitStruct.ClockDivision = LL_TIM_CLOCKDIVISION_DIV1;LL_TIM_Init(TIM3, &TIM_InitStruct);LL_TIM_DisableARRPreload(TIM3);LL_TIM_SetClockSource(TIM3, LL_TIM_CLOCKSOURCE_INTERNAL);LL_TIM_SetTriggerOutput(TIM3, LL_TIM_TRGO_RESET);LL_TIM_DisableMasterSlaveMode(TIM3);LL_TIM_IC_SetActiveInput(TIM3, LL_TIM_CHANNEL_CH2, LL_TIM_ACTIVEINPUT_DIRECTTI);LL_TIM_IC_SetPrescaler(TIM3, LL_TIM_CHANNEL_CH2, LL_TIM_ICPSC_DIV1);LL_TIM_IC_SetFilter(TIM3, LL_TIM_CHANNEL_CH2, LL_TIM_IC_FILTER_FDIV1);LL_TIM_IC_SetPolarity(TIM3, LL_TIM_CHANNEL_CH2, LL_TIM_IC_POLARITY_RISING);LL_TIM_IC_SetActiveInput(TIM3, LL_TIM_CHANNEL_CH3, LL_TIM_ACTIVEINPUT_DIRECTTI);LL_TIM_IC_SetPrescaler(TIM3, LL_TIM_CHANNEL_CH3, LL_TIM_ICPSC_DIV1);LL_TIM_IC_SetFilter(TIM3, LL_TIM_CHANNEL_CH3, LL_TIM_IC_FILTER_FDIV1);LL_TIM_IC_SetPolarity(TIM3, LL_TIM_CHANNEL_CH3, LL_TIM_IC_POLARITY_RISING);LL_TIM_IC_SetActiveInput(TIM3, LL_TIM_CHANNEL_CH4, LL_TIM_ACTIVEINPUT_DIRECTTI);LL_TIM_IC_SetPrescaler(TIM3, LL_TIM_CHANNEL_CH4, LL_TIM_ICPSC_DIV1);LL_TIM_IC_SetFilter(TIM3, LL_TIM_CHANNEL_CH4, LL_TIM_IC_FILTER_FDIV1);LL_TIM_IC_SetPolarity(TIM3, LL_TIM_CHANNEL_CH4, LL_TIM_IC_POLARITY_RISING);/* USER CODE BEGIN TIM3_Init 2 */LL_TIM_EnableIT_UPDATE(TIM3);//更新中断使能LL_TIM_EnableIT_CC2(TIM3);//捕获通道2使能LL_TIM_EnableIT_CC3(TIM3);//捕获通道3使能LL_TIM_EnableIT_CC4(TIM3);//捕获通道4使能LL_TIM_CC_EnableChannel(TIM3,LL_TIM_CHANNEL_CH2);//通道2使能LL_TIM_CC_EnableChannel(TIM3,LL_TIM_CHANNEL_CH3);//通道3使能LL_TIM_CC_EnableChannel(TIM3,LL_TIM_CHANNEL_CH4);//通道4使能LL_TIM_EnableCounter(TIM3);/* USER CODE END TIM3_Init 2 */}uint32_t  TIM3_OverCnt = 0;
int32_t  Value_Temp2 = 0;
int32_t  Value_Temp3 = 0;
int32_t  Value_Temp4 = 0;uint32_t  TIM3_CH2_Capture_FristValue_1; 
uint32_t  TIM3_CH2_Capture_FristValue_2; 
uint32_t  TIM3_CH2_Capture_FristValue_3; 
uint32_t  TIM3_CH2_Capture_HighLevel; 
uint32_t  TIM3_CH2_Capture_LowLevel; 
uint8_t   TIM3_CH2_CaptureNumber;
//uint32_t  TIM3_CH2_Freq = 0;
//float 	  TIM3_CH2_Duty = 0;uint32_t  TIM3_CH3_Capture_FristValue_1; 
uint32_t  TIM3_CH3_Capture_FristValue_2; 
uint32_t  TIM3_CH3_Capture_FristValue_3; 
uint32_t  TIM3_CH3_Capture_HighLevel; 
uint32_t  TIM3_CH3_Capture_LowLevel; 
uint8_t   TIM3_CH3_CaptureNumber;
//uint32_t  TIM3_CH3_Freq = 0;
//float 	  TIM3_CH3_Duty = 0;uint32_t  TIM3_CH4_Capture_FristValue_1; 
uint32_t  TIM3_CH4_Capture_FristValue_2; 
uint32_t  TIM3_CH4_Capture_FristValue_3; 
uint32_t  TIM3_CH4_Capture_HighLevel; 
uint32_t  TIM3_CH4_Capture_LowLevel; 
uint8_t   TIM3_CH4_CaptureNumber;void TIM3_CallBack(void)
{	//------------------------------------------CC2if(LL_TIM_IsActiveFlag_CC2(TIM3)){		LL_TIM_ClearFlag_CC2(TIM3);if(TIM3_CH2_CaptureNumber == 0){TIM3_OverCnt = 0;TIM3_CH2_CaptureNumber = 1;	
//					  LL_TIM_SetCounter(TIM3,0);	}elseif(TIM3_CH2_CaptureNumber == 1){	TIM3_CH2_Capture_FristValue_1 = LL_TIM_IC_GetCaptureCH2(TIM3);	// 获取当前的捕获值. 即CCRx2  //设置下降沿触发LL_TIM_IC_SetPolarity(TIM3,LL_TIM_CHANNEL_CH2,LL_TIM_IC_POLARITY_FALLING);						TIM3_CH2_CaptureNumber = 2;TIM3_OverCnt = 0;						}elseif(TIM3_CH2_CaptureNumber == 2){TIM3_CH2_Capture_FristValue_2 = LL_TIM_IC_GetCaptureCH2(TIM3);	// 获取当前的捕获值. 即CCRx2  if(TIM3_OverCnt >= 1){								 						TIM3_CH2_Capture_HighLevel = TIM3_OverCnt * 65535 + TIM3_CH2_Capture_FristValue_2 - TIM3_CH2_Capture_FristValue_1;			}else{Value_Temp2 = TIM3_CH2_Capture_FristValue_2 - TIM3_CH2_Capture_FristValue_1;Value_Temp2 = Value_Temp2>0?Value_Temp2:0;							TIM3_CH2_Capture_HighLevel = TIM3_OverCnt * 65535 + Value_Temp2;}											//设置上升沿触发LL_TIM_IC_SetPolarity(TIM3,LL_TIM_CHANNEL_CH2,LL_TIM_IC_POLARITY_RISING);		TIM3_CH2_CaptureNumber = 3;TIM3_OverCnt = 0;}elseif(TIM3_CH2_CaptureNumber == 3){TIM3_CH2_Capture_FristValue_3 = LL_TIM_IC_GetCaptureCH2(TIM3);	// 获取当前的捕获值. 即CCRx2  if(TIM3_OverCnt >= 1){TIM3_CH2_Capture_LowLevel = TIM3_OverCnt * 65535 + TIM3_CH2_Capture_FristValue_3 - TIM3_CH2_Capture_FristValue_2;							}else{Value_Temp2 = TIM3_CH2_Capture_FristValue_3 - TIM3_CH2_Capture_FristValue_2;Value_Temp2 = Value_Temp2>0?Value_Temp2:0;TIM3_CH2_Capture_LowLevel = TIM3_OverCnt * 65535 + Value_Temp2;							}//					//设置    沿触发LL_TIM_IC_SetPolarity(TIM3,LL_TIM_CHANNEL_CH2,LL_TIM_IC_POLARITY_FALLING);				TIM3_CH2_CaptureNumber = 4;TIM3_OverCnt = 0;}		elseif(TIM3_CH2_CaptureNumber == 4){//					//设置    沿触发LL_TIM_IC_SetPolarity(TIM3,LL_TIM_CHANNEL_CH2,LL_TIM_IC_POLARITY_RISING);				TIM3_CH2_CaptureNumber = 1;TIM3_OverCnt = 0;}					}		//------------------------------------------CC3if(LL_TIM_IsActiveFlag_CC3(TIM3)){	LL_TIM_ClearFlag_CC3(TIM3);if(TIM3_CH3_CaptureNumber == 0){TIM3_OverCnt = 0;TIM3_CH3_CaptureNumber = 1;	
//					  LL_TIM_SetCounter(TIM3,0);	}elseif(TIM3_CH3_CaptureNumber == 1){TIM3_OverCnt = 0;TIM3_CH3_Capture_FristValue_1 = LL_TIM_IC_GetCaptureCH3(TIM3);	// 获取当前的捕获值. 即CCRx2  //设置下降沿触发LL_TIM_IC_SetPolarity(TIM3,LL_TIM_CHANNEL_CH3,LL_TIM_IC_POLARITY_FALLING);						TIM3_CH3_CaptureNumber = 2;					}elseif(TIM3_CH3_CaptureNumber == 2){TIM3_CH3_Capture_FristValue_2 = LL_TIM_IC_GetCaptureCH3(TIM3);	// 获取当前的捕获值. 即CCRx2  if(TIM3_OverCnt >= 1){			TIM3_CH3_Capture_HighLevel = TIM3_OverCnt * 65535 + TIM3_CH3_Capture_FristValue_2 - TIM3_CH3_Capture_FristValue_1;							}	else{Value_Temp3 = TIM3_CH3_Capture_FristValue_2 - TIM3_CH3_Capture_FristValue_1;Value_Temp3 = Value_Temp3>0?Value_Temp3:0;						TIM3_CH3_Capture_HighLevel = TIM3_OverCnt * 65535 + Value_Temp3;}	//设置上升沿触发LL_TIM_IC_SetPolarity(TIM3,LL_TIM_CHANNEL_CH3,LL_TIM_IC_POLARITY_RISING);			TIM3_CH3_CaptureNumber = 3;TIM3_OverCnt = 0;}elseif(TIM3_CH3_CaptureNumber == 3){TIM3_CH3_Capture_FristValue_3 = LL_TIM_IC_GetCaptureCH3(TIM3);	// 获取当前的捕获值. 即CCRx2  if(TIM3_OverCnt >= 1){					TIM3_CH3_Capture_LowLevel = TIM3_OverCnt * 65535 + TIM3_CH3_Capture_FristValue_3 - TIM3_CH3_Capture_FristValue_2;								}	else{Value_Temp3 = TIM3_CH3_Capture_FristValue_3 - TIM3_CH3_Capture_FristValue_2;Value_Temp3 = Value_Temp3>0?Value_Temp3:0;							TIM3_CH3_Capture_LowLevel = TIM3_OverCnt * 65535 + Value_Temp3;}	//					//设置    沿触发LL_TIM_IC_SetPolarity(TIM3,LL_TIM_CHANNEL_CH3,LL_TIM_IC_POLARITY_FALLING);	TIM3_CH3_CaptureNumber = 4;TIM3_OverCnt = 0;}		elseif(TIM3_CH3_CaptureNumber == 4){//					//设置    沿触发LL_TIM_IC_SetPolarity(TIM3,LL_TIM_CHANNEL_CH3,LL_TIM_IC_POLARITY_RISING);		TIM3_CH3_CaptureNumber = 1;TIM3_OverCnt = 0;}				}//------------------------------------------CC4if(LL_TIM_IsActiveFlag_CC4(TIM3)){	LL_TIM_ClearFlag_CC4(TIM3);if(TIM3_CH4_CaptureNumber == 0){TIM3_OverCnt = 0;TIM3_CH4_CaptureNumber = 1;	
//					   LL_TIM_SetCounter(TIM3,0);	}elseif(TIM3_CH4_CaptureNumber == 1){TIM3_OverCnt = 0;TIM3_CH4_Capture_FristValue_1 = LL_TIM_IC_GetCaptureCH4(TIM3);	// 获取当前的捕获值. 即CCRx2  //设置下降沿触发LL_TIM_IC_SetPolarity(TIM3,LL_TIM_CHANNEL_CH4,LL_TIM_IC_POLARITY_FALLING);			TIM3_CH4_CaptureNumber = 2;}elseif(TIM3_CH4_CaptureNumber == 2){TIM3_CH4_Capture_FristValue_2 = LL_TIM_IC_GetCaptureCH4(TIM3);	// 获取当前的捕获值. 即CCRx2  if(TIM3_OverCnt >= 1){					TIM3_CH4_Capture_HighLevel = TIM3_OverCnt * 65535 + TIM3_CH4_Capture_FristValue_2 - TIM3_CH4_Capture_FristValue_1;								}	else{Value_Temp4 = TIM3_CH4_Capture_FristValue_2 - TIM3_CH4_Capture_FristValue_1;Value_Temp4 = Value_Temp4>0?Value_Temp4:0;							TIM3_CH4_Capture_HighLevel = TIM3_OverCnt * 65535 + Value_Temp4;}	//设置上升沿触发LL_TIM_IC_SetPolarity(TIM3,LL_TIM_CHANNEL_CH4,LL_TIM_IC_POLARITY_RISING);			TIM3_CH4_CaptureNumber = 3;TIM3_OverCnt = 0;}elseif(TIM3_CH4_CaptureNumber == 3){TIM3_CH4_Capture_FristValue_3 = LL_TIM_IC_GetCaptureCH4(TIM3);	// 获取当前的捕获值. 即CCRx2  if(TIM3_OverCnt >= 1){									TIM3_CH4_Capture_LowLevel = TIM3_OverCnt * 65535 + TIM3_CH4_Capture_FristValue_3 - TIM3_CH4_Capture_FristValue_2; 								}	else{Value_Temp4 = TIM3_CH4_Capture_FristValue_3 - TIM3_CH4_Capture_FristValue_2;Value_Temp4 = Value_Temp4>0?Value_Temp4:0;							TIM3_CH4_Capture_LowLevel = TIM3_OverCnt * 65535 + Value_Temp4; }	//					//设置    沿触发LL_TIM_IC_SetPolarity(TIM3,LL_TIM_CHANNEL_CH4,LL_TIM_IC_POLARITY_FALLING);	TIM3_CH4_CaptureNumber = 4;TIM3_OverCnt = 0;}		elseif(TIM3_CH4_CaptureNumber == 4){//					//设置    沿触发LL_TIM_IC_SetPolarity(TIM3,LL_TIM_CHANNEL_CH4,LL_TIM_IC_POLARITY_RISING);		TIM3_CH4_CaptureNumber = 1;TIM3_OverCnt = 0;}				} //------------------------------------------Updateif(LL_TIM_IsActiveFlag_UPDATE(TIM3)){	LL_TIM_ClearFlag_UPDATE(TIM3); //每次溢出时间为65536usTIM3_OverCnt++;}}

#ifndef __TIM_H__
#define __TIM_H__#ifdef __cplusplus
extern "C" {
#endif/* Includes ------------------------------------------------------------------*/
#include "main.h"void MX_TIM2_Init(void);
void MX_TIM3_Init(void);
void TIM3_CallBack(void);#ifdef __cplusplus
}
#endif#endif /* __TIM_H__ */

#include "main.h"
#include "tim.h"
#include "gpio.h"void SystemClock_Config(void);int main(void)
{HAL_Init();SystemClock_Config();MX_GPIO_Init();MX_TIM2_Init();MX_TIM3_Init();while (1){}}

/*** @brief This function handles TIM3 global interrupt.*/
void TIM3_IRQHandler(void)
{TIM3_CallBack();}

查看全文

http://www.yayakq.cn/news/759143/

辽宁建设厅网站官方app下载

学校网站建设命名个人主页中不会展示下列哪项内容

防腐木用什么名字做网站厦门企业app开发

中国建设银行网站首页joy网站备案备注关联性

丹阳高铁站对面的规划互联网公司大厂排名

建设网上银行官方网站空间里怎么放多个网站

百度手机模板网站福田建设网站

做网站是要云空间吗奉节县关键词seo排名优化

做外贸站推广电商店铺首页设计

铁哥们网站建设哪些网站可以做视频搬运

变白网站制作源码wordpress图像验证码

繁昌网站建设内容营销模式

网站是什么样的建设网站需要给钱吗

成都快速建站模板网站建设定制网站建设公司哪家好

成都电子商务网站什么叫个人网站软件

58同城合肥网站建设北京软件开发培训

电子商务网站开发教程课后答案制作一个简单网站

网站背景房地产网络推广方案

网站建设资讯版块如何做用户运营最吉利旺财的建筑公司名字

中山营销网站建设移动端h5是什么意思

php网站开发指导教材文献注册一个公司需要什么条件

做软件的公司网站有哪些乐都企业网站建设多少钱

江西网站制作如何选择合肥网站建设

网站开发框架有哪些企业seo推广外包

网站的定位与功能淘宝网免费素材图库

网站的服务与建设岗位职责wordpress用户角色管理系统

常德网站公司城市人家装饰公司怎么样

网站备案后更换主机贵阳网站建设多钱钱

大理公司网站建设做网站英文

网站建设需要会什么软件有哪些内容百度快照直接进入网站

相关文章：